When a restaurant, shop, or plant adds equipment, the electrical work is usually the part that decides whether it actually runs. A dedicated circuit, the right disconnect, a correctly sized breaker, and a clean termination. That is the job.
You buy the equipment. We do not supply ovens, coolers, compressors, or machines. We read the nameplate, check the existing service, and install the circuit and connections the manufacturer requires.
Retrofits are the same idea on gear that is already there: a replacement unit on an old circuit, a relocated machine, or a disconnect that should have been there the first time.
Many customers pair equipment installation & retrofit with commercial electrical and commercial troubleshooting. Not sure where to start? Read signs you need an electrical panel upgrade in Polk County.
Serving Polk County: Lake Wales, Winter Haven, Bartow, Haines City, Lakeland, Dundee, Frostproof, Auburndale, Polk City, Davenport, Fort Meade, Lake Alfred, and the surrounding Central Florida communities. Call (863) 676-0198 to book.
“Kincaid did an excellent job adding outlets to my garage apartment. Their final fee matched their quote and they cleaned up and it was like they were never there!! (Except for the new outlets) Can’t stress enough the value of an honest electrician!”
How An Equipment Job Runs
- 1
Nameplate and service
Voltage, phase, full-load amps, and whether the existing panel can carry it. If it cannot, the panel work is quoted separately.
- 2
Circuit and disconnect
A dedicated run, correctly sized, with the disconnect where code and the manufacturer want it.
- 3
Connect and test
Terminated to the unit you supplied, then tested. We do not leave a machine half-wired for someone else to finish.
Typical Equipment Work
New Installs
- Dedicated circuits for kitchen, shop, and plant equipment
- Disconnects, receptacles, and hardwired connections
- Nameplate load calculation against the existing service
- Permitted work and inspection where required
Retrofits
- Replacement equipment on an existing circuit, resized if needed
- Relocating a machine and extending or rerouting the feed
- Adding a local disconnect that was never installed
- Correcting undersized conductors or the wrong breaker
Commercial Kitchen Equipment Electrical Installation For Restaurants
Commercial kitchen equipment electrical installation begins with the nameplate. Ovens, fryers, coolers, dishwashers, and mixers each have a voltage, phase, and amp requirement that the circuit must match. We read the data, check the existing panel for capacity, and install the circuit, disconnect, and connections the manufacturer calls for.
You buy the equipment. We do not supply the unit, which keeps the electrical scope clear. Kitchen work is often done after close so the line is not down during service. If a replacement unit draws more than the old one, we tell you before work starts so the right wire size and breaker are used.
Do You Need A Dedicated Circuit For Commercial Equipment?
A dedicated circuit for commercial equipment means the machine has its own breaker and wiring, shared with nothing else. Many pieces of equipment require it, particularly motors, compressors, and heating loads, because they draw high or varying current. Sharing a circuit invites nuisance trips and can overheat wiring that was never sized for the combined load.
The nameplate and the manufacturer instructions tell us what is required. We size the conductors and breaker to match and place the disconnect where the code and the unit call for it. If the existing panel cannot carry the new load, that is quoted separately so you can plan and decide before the work begins.
Why Equipment Disconnect Installation Matters For Safety And Service
A disconnect lets someone shut off power to a machine at the machine. That matters when a technician has to service a motor, compressor, or oven and needs to be sure it cannot start. Equipment disconnect installation is also a common code requirement, which is why inspectors look for it on new and replacement equipment.
Older installations sometimes never had one, or it sits too far from the unit to be useful. We add a local disconnect, sized and rated for the load, in a location that is reachable and clear. Doing it right once makes later repairs faster and safer for your own staff and for outside service techs.
Electrical Retrofit For Commercial Equipment In An Occupied Space
An electrical retrofit for commercial equipment covers the situations where gear already exists but the wiring no longer fits. A replacement unit may need a larger circuit. A machine may be moving across the room and need its feed extended. A disconnect may be missing, or the breaker may not match the nameplate. These are small jobs with large effects on reliability.
We work in spaces that are open for business, so we plan around your hours and keep the work area tidy. Before we start, we check what is wired now, not what the old drawings say. Undersized conductors and wrong breakers are common findings, and we quote the correction as its own line so nothing is buried in the price.
Three-Phase Equipment Wiring For Shops And Light Industrial Properties
Three-phase equipment wiring needs care with phase rotation, voltage, and balanced loads. Compressors, large coolers, and shop machines rely on three-phase power for smooth running and efficiency. A wrong connection can run a motor backward or damage it, so the supply is tested before the machine is connected and the direction is checked when it starts.
First we confirm the building actually has the service the equipment needs. If not, the panel or service work is a separate scope. We install the feeder, disconnect, and termination to match the nameplate and test the result. We do not leave a machine half-wired, and we do not supply the equipment itself.
Ready to book equipment installation & retrofit?
Licensed, family owned, and working out of Lake Wales since 1973. Upfront pricing, and a real person on the phone.
Other Commercial Services
Equipment Installation & Retrofit Across Polk County
The same crew covers the whole service area. Pick your city for local detail, or just call us.
Lake Wales/Winter Haven/Bartow/Haines City/Lakeland/Dundee/Frostproof/Auburndale/Polk City/Davenport/Fort Meade/Lake Alfred
Equipment Installation & Retrofit FAQs
Do you sell the equipment?
No. You purchase the cooler, oven, compressor, or machine. We install the electrical: the circuit, the disconnect, and the connections.
Can you work around our hours?
Yes. Kitchen and shop retrofits are often done after close so the line is not down during service.
What if the existing circuit is too small?
We tell you before we start. Undersized conductors and the wrong breaker are common on replacement units. The new circuit is quoted as its own line, not buried in a surprise.