Skip to content
Kincaid Electrical Services, Inc. logo
Hands holding a multimeter against a kitchen outlet, with a toaster and coffee maker unplugged

Outlets that stopped working in one room

Published

Outlets not working is one of the most common electrical questions people ask. In a house around Lake Wales it is rarely the whole panel. It is one receptacle, one wall, or one room, and the cause is usually upstream of the dead opening.

This is the order we use on an electrical repair call. It keeps a simple reset from turning into a box that has been taken apart for no reason.

One outlet or the whole wall

If a single receptacle is dead and the one next to it works, the fault is often in that device: a loose backstab, a broken neutral, or a receptacle that has failed. If every outlet on one wall is dead, the first device in the chain has opened, or a GFCI ahead of them has tripped.

Write down what still works. The refrigerator, the microwave, and the bedroom lights tell us whether this is one circuit or a bigger loss of power. A lamp you can carry is a better test than an expensive appliance.

The GFCI you are not looking at

A dead bathroom, a dead garage, or a dead outdoor outlet is a GFCI until it is proven otherwise. The device that protects them may be in another room. Reset that device with everything unplugged. If it trips again at once, there is a fault, and resetting it all afternoon will not clear the fault.

Kitchens are the same pattern. One GFCI on the counter can feed the other counter openings. The dead outlet is not always the one that needs the new device.

Kitchen counter with a coffee maker, a toaster, and a GFCI outlet with test and reset buttons
A kitchen GFCI can be the reason several other outlets are dead. Reset this device before the other receptacles are replaced.

The breaker that looks on

A tripped breaker sometimes sits in the middle, not fully off. Push it firmly off, then on. A breaker that will not stay on is protecting a short or an overload. Leave it off. A breaker that stays on and the outlets are still dead means the problem is out in the circuit, not in the handle.

Half the house dark, with some 240-volt appliances dead, is a different problem. That can be a lost leg from the utility or a failed connection at the main. It is not a single outlet repair. Stay out of the panel and call.

Backstabs and worn receptacles

Houses from the 1970s through the 1990s in this county are full of receptacles that were stabbed in the back instead of landed on the screws. The spring loosens. The outlet works when you push on the plug and dies when you let go. The repair is a new receptacle, with the conductors on the screws, and a look at the other devices on that circuit while the box is open.

A receptacle that is warm, discolored, or will not hold a plug is done. Replacing it is straightforward. If the wire insulation is burned, the box needs more than a new device.

Hands holding a multimeter against a kitchen outlet, with a toaster and coffee maker unplugged
A meter on a kitchen outlet. Voltage at the device tells us whether the circuit is open upstream or the receptacle itself has failed.

What a meter changes

We meter the dead device for voltage, then the next box upstream, then the panel if the circuit never appears. An open neutral can make a tester lie and can damage equipment that is still plugged in. That is why guessing with a $5 night-light is only the first step.

Aluminium branch wiring, when we find it, is called out. It is not repaired by stabbing a new receptacle onto the old conductors. The connection has to be listed for that wire.

When to stop and call

You can reset a GFCI and a breaker, and you can unplug the space heater that was sharing the circuit with a microwave. Past that, the work is inside a live box. A burning smell, a scorched plate, or outlets dead on both floors at once should stay switched off until someone looks at them.

The outlet repair page describes the work. Shop hours are Monday through Friday, 7:30 AM to 4:30 PM. The number is (863) 676-0198, or use the contact page. Florida master license EC0000873. The shop is at 15510 Hwy 27, Lake Wales, FL 33859.

More from us: all electrical services and the cities we serve.

Call the shop

Monday through Friday, 7:30 AM to 4:30 PM. Tell us the problem and we will say when we can come.

Call NowSchedule